Trophy Preparation

 

thumbnails

Hide Thumbs

First

Previous

Pause

Next

Last

Set Speed Slideshow speed: 5 seconds

Move

trophy

• 
  head mount
• 
  measuring guide
• 
  cuts for skull cap

 

Aim

The aim of this guide is to provide practical guidance on the preparation of trophy heads.
If heads are to be cut on a regular basis, then it is recommended that a jig be purchased, as this gives an accurate and consistent line of cut.

Antler mount preparation

As part of the general lardering process, the head and in certain cases, the jaw of the animal will be removed*.

Skinning

• Skinning the head prior to boiling is optional. If skin is to be left on, make a cut through the skin over the top of the nose and through the sinew in the roof of the mouth.
  Skin the head by incising from the back of the mouth opening, and cut in a dirct line to the back of the head. Then skin upwards towards the eye sockets, nose and coronets, following the contours of the skull

Boiling

Boiling time is dependent on the animal’s age and species and can vary from 15 to 30 minutes, or more for larger species. The smaller the species and younger the animal, the less time boiling time required, otherwise the bones will fall apart. If the two nose bones at the front come away, then bleach separately, dry and superglue into position.

• Before boiling the head ensure the eyes have been removed or punctured.
• Place the skull in boiling water with added soda/washing powder and with the coronets above the water line. Clamps may assist with the boiling process.
• Take care not to over-boil particularly for long and full cuts (Figure 1: A & B). A good indication that the head is ready is the splitting and shrinking of the membrane over the nose.
• Dip the head in cold water and remove the meat and sinews with a blunt knife or a pressure washer.
• From the underside of the skull break out the unwanted bone and nasal passages using pliers and a knife.
• Finish off by scrubbing the skull with a stiff nailbrush or similar implement, taking care around the delicate nose bones in the long and full cut (Figure 1: A & B).

Cutting

• Cutting can be carried out before or after boiling depending on preference. Laying the head on its side, mark out a line to cut with the point of a knife.
• Before performing the short nose cut (Figure 1:C only), remove the eyes.
• Place the head in an adjustable cutting clamp or hold the skull and antlers firmly on the bench. Carefully, using a saw, make the desired cut (see Figure 1: A to D).
• Without use of a cutting clamp, take care to keep the cut square from side to side. Once cutting has started, sight along the saw blade across the nose to ensure that the line will emerge at a similar level on the other side.

Any unevenness in the cut can be removed later by sanding when the skull has dried out completely (a mask should be worn for this process). Remove the brains after cutting.

Bleaching

• Ensure necessary protective clothing such as rubber gloves and eye protection is worn for this part of the procedure.
• Carry out this process while the skull is still wet. If it has dried out, then re-soak for a number of hours.
• Use a solution of hydrogen peroxide (30%). Comply with the manufacturer’s recommendations and note any warning labels relating to Control of Substances Hazardous to Health Regulations 2002 (COSHH)1,2.
• Take care not to get bleach on the coronets or antlers.
  Before bleaching the outer skull, paint the cavities on the underside with bleach. This helps cure it and remove unwanted smells.
• Place cotton wool or absorbent paper round all the contours of the outer skull, ending immediately below the coronets, then paint with bleaching agent. Paint again after three hours if required.
• The bleaching time will again depend on the species and age of the animal and the concentration of the hydrogen peroxide used. If using 30% concentration the bleach may be left on for several hours up to 12 hours (i.e. overnight). Weaker solutions may require longer. The use of household bleach should be avoided as this may weaken the skull and cause the bone to crumble.
• Leave the kull to dry.

Trophy Measurement

Where a head may be worthy of a medal, present for measurement as full skull trophy, prepared as described with the lower jaw removed. Heads should be prepared in the normal way with the lower jaw removed. Note, the use of artificial colouring will not be accepted in trophy measuring.

Export

Trophies should be cleaned of all flesh and bleached (disinfected). Antlers should be wrapped and packed securely so as to present no sharp edges. Heads prepared in this way may be transported as luggage.
Where there are national animal health restrictions in place check with the local Animal Health Office for guidance2.
Full-mounts and accompanying capes require to be prepared at point of origin and are best transported to a taxidermist by carrier.

Jump to top